Setting
Currency
0 Item(s)

You have no items in your shopping cart.

#309-562 ThunderMax® With Wave Tune For 2014-2015 H-D® Trike Models Double click on above image to view full picture

ThunderMax® With AutoTune For 2009-2016 Trike Models

$0.00

Overview

ThunderMax® is an industry award winning, performance ECM designed specifically for EFI equipped Harley Davidson® motorcycles. This highly advanced, stand-alone tuning system utilizes proprietary AutoTune technology specificly designed to interface with wide-band oxygen sensors to automaticly adjust a wide range throttle positions and RPM ranges to deliver unmatched performance and driveability like no other product in the industry. ThunderMax® is made in the USA and comes 100% assembled, ready to install with no wire-cutting or splicing required. Simply replace the factory ECM and oxygen sensors, load a map, and enjoy your new ride!

In compliance with ARB emissions laws, this product is not sold or shipped to California.

Select the ThunderMax for your application below.

Would you like to have your ThunderMax pre-programmed for your application?

* Required Fields

Details

How You Ride, Where You Ride, Every Ride!
Would you like to have full control of your EFI system, freedom to make major or minor engine changes or tuning adjustments without a master’s degree in electronics and computers? Here is a simple solution—ThunderMax® with Wave Tune AutoTune! The ThunderMax® is a completely new product that replaces the factory electronic control module (ECM), not an add-on box or post-fuel signal modifier. The ThunderMax® is purpose-built to deliver uncompromising performance with advantages not possible with post-fuel or flash systems - but you don’t have to be a rocket scientist to install, program or make adjustments to it.

Just how easy is it? Installation is a straightforward plug-in replacement of the factory module and oxygen sensors*1. The ThunderMax® TMax Tuner software contains hundreds of base maps that cover most popular factory and aftermarket combinations, dyno-developed on real motorcycles. Choosing a map is a quick and easy process thanks to TMax Tuner’s sorting filters; loading a map takes less than a minute. After that, you’re ready to let the ThunderMax’s Wide-Band AutoTune system dial in idle and warm-up settings for your engine and you’re ready to ride!

During your ride, every time you ride, ThunderMax’s® Wave Tune AutoTune analyzes, adjusts and anticipates the air/fuel ratio read by the wide-band oxygen sensors at warp speed during every cylinder fire and makes any necessary adjustments to the injector pulse width to achieve the desired air/fuel ratio while compensating for variations in injectors, fuel pressure and exhaust flow. With every tank of fuel, at every temperature or elevation. That’s it! All you have to do is ride.

As simple as it is to install and use, don’t be fooled into thinking that this not one of the most sophisticated systems you can buy for your Harley®. Using the supplied Tuner software, you can adjust or monitor virtually every parameter of the system:

    • Idle Speed & Rev Limit
    • Closed Loop AFR Targets
    • Igniting Timing
    • Accel Pump Simulation
    • Start Fuel Pulse
    • Decel Pop Control
    • Speedometer Calibration
    • Read Diagnostic Codes
    • Running Statistics / Logs
    • Engine Temp Alarm
    • Live Engine Tuning
    • Live Monitoring & Recording
    • Dealer Digital Tech Compatible
    • Warm-up Settings
    • And More!


While this system does not require a dyno to achieve a smoother, cooler, excellent running engine, that does not mean it’s not a dyno-friendly device! Experienced tuners will appreciate its live-tuning capabilities with real-time monitoring and the ability to control all of the systems tuning parameters, knowing that AutoTune will keep the final tune from deteriorating as ambient conditions change. Advanced level software is available for technicians wishing to create a custom tune, add nitrous or install a forced-induction intake.

ThunderMax® also employs industry-leading tech support though its internal data-collection system that quickly communicates directly with the ThunderMax® support team should there ever be a need. ThunderMax® Technicians can quickly review recorded data streams, data stored within the module and information about the bike and system with just a few clicks of a mouse!

The ThunderMax® makes more sense in the long run as the system can grow and change as your engine does—just load a new map! ThunderMax® software, firmware and maps updates are accessible 24/7 with an Internet connection so you’re only a mouse-click away from the latest available data. Each ThunderMax® includes an ECM, 2 wide-band oxygen sensors with harness, communication cable, software disk and comprehensive instructions. The ThunderMax® is designed and manufactured right here in the USA and backed by a 3-year warranty!

*1 ThunderMax® uses 18mm Wide-Band oxygen sensors, which unlike the factory narrow-band sensors read over the engines full rpm range for constant full-time feedback and adjustments. Certain year bike exhaust systems are equipped with 18mm sensor ports, others may have 12mm ports or none at all. Check application notes for compatibility.

Download the ThunderMax® software for free! CLICK HERE!

SPECIAL NOTE FOR 2010 AND LATER TOURING MODELS -
ThunderMax® includes wide-band, 5-wire oxygen sensors that thread into 18mm x 1.5mm bungs located near the exhaust port, same thread size and location as stock narrow-band, 2-wire sensors used on 2008 and 2009 Touring model exhausts. Starting with 2010 models, all Touring bikes are equipped with a catalytic converter in the headpipe collector area. The oxygen sensors used by H-D® on 2010 and later Touring models are smaller (12mm threads) heated 4-wire, narrow-band sensors located just forward of the catalytic converter near the transmission. The ThunderMax® sensors must be mounted in the 2008-2009 location, up near the cylinder head exhaust port. If you are retaining the original equipment 2010 and later exhaust header or have already purchased a pipe configured for 2010-up style 12mm sensors, 18 x 1.5mm bungs will need to be added to the existing headers in the upper location (near the exhaust port as on 2008 and 2009 models), with the lower 12mm sensors removed and ports capped. If using a not-yet-purchased aftermarket exhaust pipe, order an exhaust system for a 2009 model (pipe fitment is the same for 2010-2013 models) and your ThunderMax® sensors will install without modification. If you already have an aftermarket exhaust designed for a 2010 and later model Touring bike, you will need to install bungs as mentioned previously if the system is not equipped with dual bung locations.

 

This product is not for sale or use on pollution controlled vehicles.

Product Tags

Use spaces to separate tags. Use single quotes (') for phrases.

Customer Reviews

2 Item(s)

Much better throttle response right out of the box Review by CW
Price
Value
Quality
“Much better throttle response right out of the box!”

C.W. - WY (Posted on 9/28/2017)
Great product and Great Performance Review by Den
Price
Value
Quality
I installed this on my 2012 FLHTCUTG with H.D. 2009 Headers. I also installed H.D. 255 cams, H.D. adj. chromemoly push rods, H.D. roller rockers and new heavy duty cam bearings. I installed the map that I chose from your files. I had to change the final drive ratio to get the speedometer to read correct. I now have 7,000 miles on this set up, 34-36mpg and it runs cool even at 90F plus degrees in New Mexico at 6000' altidue. This is my 3rd T-Max and I think they are excellent. Thank you Zippers! (Posted on 6/8/2015)

2 Item(s)

Write Your Own Review

You're reviewing: ThunderMax® With AutoTune For 2009-2016 Trike Models

How do you rate this product? *

  1 star 2 stars 3 stars 4 stars 5 stars
Price
Value
Quality

Additional Information

Brand ThunderMax®
Fuel / Air EFI
Model Trike/Tri Glide®
Engine Type Twin Cam®
Emissions Compliant No
Loading...
Loading...